Check items to add to the cart or select all
-
Jabsco Wakeboard Ballast Puppy Reversible PumpOur Price: $199.95
You're currently on:
Specifications
Material: Space Age Nitrile PolymerShaft Diameter: 5/16" (8mm)
Impeller Depth: 7/8" (22mm)
Number of Blades: 6
Impeller Diameter: 2 " (51mm)
Insert Material: Plastic
Jabsco Part #: 6303-0107
OEM Application: MasterCraft, Correct Craft (Air Nautique), Supra, Moomba, Yamaha, and Centurion
If you've been having problems with your system draining or filling correctly, or if water is leaking into or out of the tanks or bags while the pumps are turned off, the green ballast pump impeller is designed to fix that completely.
Impellers are a wear item, so over time the efficiency of the pump will be reduced as the compound of the impeller breaks down. That means your wakeboard ballast system will take longer to fill and drain than it did when newer. Replacing a damaged or worn out impeller will restore the speed and functionality of your Jabsco Ballast Puppy pump to like new condition. If you have an original Jabsco Ballast Puppy with a black rubber or yellow neoprene impeller this is a great upgrade you can make to increase the speed and functionality of your system.
If you've installed additional bags on top of your factory hard tank ballast system (as is popular in Mastercraft and Nautique wakeboard boats) then this upgrade is essential in order to ensure that both the tank and bag will fill completely, and stay full while wakesurfing and wakeboarding.
HOW-TO: Change the Impeller on a Jabsco Ballast Puppy Pump
MasterCraft Jabsco Ballast Puppy Pump Impeller Replacement Instructions:
Step 1: Remove two of the front cover screws. (Note: Retain the screws for the reinstallation process) Swing the cover up and out of the way to allow access to the impeller location. the impeller may be black, yellow or green depending on the age of the pump.
Step 2: Using needle-nose pliers, pull the old impeller out of the casing.
Step 3: Install the new impeller. (It is intentionally larger than the case. While gently squeezing it in, ensure that the paddle wheels angle in the same direction--counterclockwise--all the way around.)
Step 4: Slide the plate back into place. NO SILICONE IS NECESSARY due to the built-in gasket, tightening the screws should prevent leakage.
Part # Cross References
This part is a direct replacement for any Jabsco impeller part number that begins with 6303, including: 6303-0007, 6303-0023, 6303-0001, 63003 0003, 6303 0003, 6303 0023 or 6303-003.
NOTE: The Jabsco Green Ballast Impeller is also the replacement upgrade impeller for the Johnson Ultra Ballast Reversible Pump. Jabsco Ballast Puppy Impellers have been confirmed compatible with Johnson Ultra Ballast Pumps.
-
great product and was easy to install, time will tell how it holds up
Review by Ray on 1/10/12Quality Price Value this product seems to have sped up the filling operations of the two v drive sacs I have it connected to, but I have not actually timed it old vs new impeller.
-
Pretty good build
Review by Green Impeller by Jabsco on 8/23/11Quality Price Value This part is a bit softer than the standard black rubber materials that are used on the ballast pump. I ordered one after my center ballast went out and have to order to more as my left and right ballast went out at the same time after 4 seasons of use. The impeller has a pretty good quality build from what it appears to be and was gently greased prior to packaging to ensure sustainability. Not sure how long these will last but hopefully longer than the stock part.
-
great
Review by grant on 8/1/11Quality Price Value the jabsco greens are the way to go if your factory ballast impellers have gone out, or you are looking to upgrade. my 2006 nastercraft x2 impellers stopped on me and i went with these. i could not be any more pleased with them. they have cut my empty/fill time by at least 50%. the pressure out of the side of the boat when emptying is amazing. the difference to me is like night and day. i highly urge you to go with these and disregard any other impellers. you will thank me if you do!
-
Poor quality
Review by Kio on 7/18/11Quality Price Value The black plastic piece in the center of the impeller failed after only a few uses allowing the motor shaft to spin without engaging the impeller. Old black ones were metal. Pretty expensive for a single use item!
NOTE: This is a defect in the impeller, and is covered under warranty if encountered. It effects and extremely small percentage of impellers, but if it does happen contact us and we'll exchange it for free.
WakeMAKERS.com Team -
New life to my pump!
Review by Stephen on 6/3/11Quality Price Value I forgot how fast my pump could pump until I replaced the impeller. My bags fill up in half the time. This is a maintenance item and should be replaced regularly like the rest of the yearly maintenance items on your boat. Very simple, remove three screws, pull out the old impeller, put in the new one, and reinstall the three screws. It could not be any easier.
-
Middle hardness works as advertised
Review by joe on 4/12/11Quality Price Value Original Puppy only used to fill had black impeller and buildup, was hard, and popped fuses. Tried yellow and my ballast would drain out by itself quickly as it was very soft. Moved to Green and it's inbetween hardness. I upgraded ballast bags from a 750 to 1100 and the Green started leaking. Sanded down the brass on the puppy and went back to black.
On a fill only puppy system, I recommend Black.
I just added another Johnson Ultra Reverse where I'll drain and fill and Green is the best way to go. -
Green Mastercraft Impeller
Review by Paul on 12/8/10Quality Price Value I have having issues with my Mastercraft's Ballast System. It was losing suction and was running really slow so I swapped out the old yellow impellers for the New Green Impellers and what do you know... They did the trick. This is the best upgrade I have done to my boat in a while. It is probably the least expensive option too.
-
Somewhat better that last flavor
Review by MC X2 on 10/3/10Quality Price Value Impeller colors for these pumps seem to change on a yearly basis. The lastest "flavotr" green seems to be the best so far (other colors being black and yellow). I did see a noticable performance imporvement on my KGB tank on my MasterCraft 07 X2. Performance on the back tanks seem to be about the same.
$38 for an impeller is stiff but much better than I've seem at other outlets. Once again Wake Makers leads the way in affordable products to keep us all on the water enjoying our hobbies. I'd love to see them expenad to include other pump maintainance items such as pump shaft seals.
Write Your Own Review
We pay YOU $5 when you review products on our website. Just submit your review, and as soon as it's approved we'll send you a coupon code you can use to save $5 on the next purchase you make.
When writing your review please try to provide detail about the specific things you like and don't like about the product. Simply saying "this is a really cool product" or "this product sucks" doesn't offer much input, instead think about WHY you feel that way, and back it up with specific examples. That will make your review more useful for other shoppers, which is the whole point. All feedback is subject to verification, and reviews that are too short, obviously made up, or inappropriate will not be approved.